NOTE:

VideoMode was released as BETA for now. Get early access by requesting to be added on the waiting list from the Add-On Store on your HoloBuilder Dashboard. Once the BETA program is completed, you will be able to get access to this capturing mode in your JobWalk app.

IMPORTANT: VideoMode is a HoloBuilder add-on that might not be included in your current license. Please contact your trusted HoloBuilder contact or reach out to our support team at support@holobuilder.com if you are interested in learning more about getting access to this feature.

VideoMode is a capturing method that allows you to simply walk the job-site while your 360° camera captures the site, without you having to take each photo individually. Simply set up the VideoMode on the JobWalk-App, locate yourself on the floor plan and HoloBuilder takes care of the rest.

The VideoMode feature analyzes the captured 360° Video and automatically organizes the corresponding 360° Photos on your floor plan, by linking the images together to an interactive tour.

With this, the VideoMode feature allows you to walk the site without stopping or interacting with your phone and increasing the quantity of 360° Photos taken, and the speed of your capturing experience with HoloBuilder. Learn more about the advantages with VideoMode here.


Let's get ready to speed up your capturing progress

Learn more on how to work with the video mode below

  1. Preparing for your job walk with VideoMode - learn more

  2. Activating VideoMode - learn more

  3. How to capture with VideoMode - learn more

  4. Uploading your video captures - learn more

  5. Additional Options - learn more

IMPORTANT:

Right now VideoMode supports the following cameras

Ricoh Theta X

Insta360 OneX (minimum firmware version on camera: 1.18.43)

Insta360 OneX2 (minimum firmware version on camera: 1.0.59)

More JobWalk App compatible cameras like e.g. Ricoh Theta Z1 or any newer cameras will possibly be supported in the future.


Preparing for your job walk with VideoMode

Note:

To get started, please always make sure to have the newest version of the JobWalk-App downloaded to your mobile Android or iOS device and log in with your HoloBuilder Account. You can learn more about how to work with the JobWalk-App in general in the dedicated article here.

Get your project ready on the app

  1. Start the JobWalk App and download/update an existing project OR create a new project - Learn more

  2. Add a new floor plan/sheet OR select an existing sheet of the project - Learn more.

  3. Tap on the sheet to open the sheet map/floor plan.


Activating VideoMode

  1. Tap on the Video-Icon on the right side of the map and choose 'Add New 360 Video'.

    Note:

    You may get the warning that your device does not meet the technical requirements for the VideoMode feature. We recommend that your device has at least 64GB of storage space to maximize the success of this feature.

  2. From the drop-down menu, choose the camera you are using and follow the instructions shown for connecting your mobile device with the camera.

    Reminder:

    Currently only the Ricoh Theta X, Insta360 OneX and Insta360 OneX2 cameras are supported with this capturing mode - more JobWalk App compatible cameras will be added in the future.

  3. Optional: After connecting the Camera for the first time, you have to choose your HDR setting:

    • HDR Off is recommended for fast image taking without tripod.

    • HDR On is recommended for higher image quality, when a tripod is used.

Note:

When capturing to an existing project, please make sure to have your HoloBuilder project downloaded/updated before connecting to the camera as you will need to be connected to the internet for the download.


How to capture with VideoMode

Best Practice:

Capture smaller videos of max. 10 minutes for different areas. This will help to keep a better overview of the processed areas, avoid errors and increase the accuracy for the linking to the sheet. You'll always see the duration of the recording displayed at the top of the screen.

Once you have connected the camera to the JobWalk App via your mobile device, you can start making use of the new VideoMode feature:

  1. Start the recording:

    1. First, name your new 360° Video Recording before capturing to get a better overview later when adding multiple recordings to a single sheet. Type in a name and tap on OK to save the name.

      HoloBuilder


    2. Next, select your starting position on the sheet - Tap on the position on the sheet where you are currently located. You will see a blue marker appear to indicate your selection.

      You can tap on a different location or drag it to adjust the position.

      Note:

      Please make sure to select your exact starting position to allow an accurate capturing and mapping of the 360° photos on the sheet.

    3. Hold the 360° camera above your head and tap on Start Recording in the JobWalk app on your mobile device to start your video. You can hold the camera in your hand, on a monopod or similar accessory.

  2. Capturing the site in VideoMode:

    1. You are now in VideoMode and can start walking the site. Make sure to keep the camera in position and avoid covering any side of the camera during your whole capture.

      1. You can also turn off the screen and store your phone in your pocket during this process.

    2. If there are any existing waypoints/Location Marker on your sheet, the images will be linked to these as TimeTravels for progress captures or new 360 images on Location Markers if close-by.

      Note:
      It is highly recommended that the video length does not exceed 10 minutes. The best practice would be to split up your walks into shorter separated tours to better control, capture and upload the documentation.
      The total length of the recorded video is shown after you complete the JobWalk.

      It is ok to lose the WiFi connection between your mobile device and the 360° camera (e.g. by going too far away from the camera with the mobile device) during the capturing process. Simply continue walking and reconnect the camera when you are done.


  3. Ending a video capture

    1. Once you have reached your destination, press End Recording on your mobile device.

    2. Select 'I am done' to finish the recording - The camera will not stop recording until you confirm to end your JobWalk by tapping on 'I'm done'.

      If you are not done with capturing in this video session, you can also return to your recording to continue the capturing in this session with 'Not yet'.

    3. Once you completed your recording with I'am done, select your exact end position on the sheet to complete the JobWalk.

      IMPORTANT:
      The end point should not be the exact same or too close to the starting point - make sure to end your walk at least 10 feet / 3m apart from the starting point indicated. Remember that the end position is roughly where your last image will be placed and you do not need to have another image on your starting position.

    4. The video will be transferred to the mobile device to connect with the project.

      IMPORTANT:

      Make sure that you do not turn off the camera or disconnect it before the video has been completely transferred to the JobWalk app. If the camera was disconnected during the capturing process, make sure to reconnect it before proceeding to the transferring of the video.


Uploading your video captures

Once a recording has been completed, you can choose to capture another or connect to a WiFi to upload your progress.

  1. Option 1: You can now 'Upload and process' the Video

  2. Option 2: Directly 'Add another 360° Video', e.g. to capture individual areas on the same level separately or add more recordings on other sheets - repeat the recording process as described above.

  3. Option 3: Continue editing your project in the JobWalk app, e.g. by adding more recordings on other sheets with 'Return to sheet'.

    Note:

    The uploading of the video directly from within the JobWalk app is only possible for shorter videos of approximately 10 minutes.
    For any longer videos, you will need to use our desktop uploader app - coming soon.


  1. Make sure to connect to a WiFi network.

  2. By tapping on Upload & process, the JobWalk app will begin to upload the video to your sheet and project in the cloud. The estimated time remaining is displayed.

    Warning:

    Please make sure not to disconnect from the WiFi, minimize the app or turn off the mobile screen

    before the upload of the video to the cloud was completed. This will help to ensure that the uploading process does not cancel.



  3. Once the upload is finished, your video gets processed in the cloud to create your waypoints on the sheet and connect the images. You will receive an Email notification when the processing is completed.

    Note:

    This processing can take up to 24 hours depending on how large the video was. You will not be able to review the updates in the cloud until the video has been processed.


Additional Options

  • Capture multiple videos per floor plan: When VideoMode is activated, you can add as many separate videos as needed to capture your site according to your requirements - Use the button "Add 360 video" and repeat the same process as described above.

  • Delete a video recording: When VideoMode is activated, tap on the three dots next to one of the listed video and select "Delete Video" - Important: You cannot undo the deletion of a video.

  • Upload a video: When VideoMode is activated, tap on the three dots next to one of the listed video and select "Upload Video" - requires a WiFi connection.

  • Looking at your documentation in the Web Editor: You can finally open your project from the HoloBuilder Dashboard in the Web-Editor once you have received an Email that the processing is completed. You will see a large amount of Waypoints created for you indicating the path of your recording. Additionally, all 360 images will be linked automatically for an interactive tour.

  • You can also add two different categories to each newly added image in the Web Editor:

    • Video Mode

    • videomode_{time_when_image_was_added}

    Based on this you can filter in the Web Editor for images added via VideoMode

If there are further questions please feel free to contact us at support@holobuilder.com to get more information.

What might also interest you:

Did this answer your question?